Using the local MQTT I do see a cumulative export figure but also expected the instantaneous export. well the current power to show positive for import and negative for export.
Is this possible without using a clamp? can the Glow MQTT show instantaneous export?
Hello @ianfretwell and @BNMBob - based on older comments in this thread, the instantaneous export question is possible with local MQTT, the challenge is meter type and firmware version.
What are yours if you know them - and if you don't, drop us a line at support and we can check. Thank you.
Hello Jane, I am waiting for my supplier to update the firmware on my Honeywell AS302P as DDC other is not supported. (i also do not see the firmware anywhere).
No I don't think my loss of MQTT export meter total data coincided with DCC migration. I lost the export total in Apr 22, and pretty sure I was switched sometime later in the year.
Hi @JaneatGlow - my meter is a Secure Liberty 100. Its been migrated over to the DCC last year. Sorry but I don't know how to get its firmware version. If you can point me at some instructions I will post back what it is.
My Meter is a EDMI ES-10B, firmware 0314B700. I'm not seeing energy export data. Energy import and power are both fine.
As its a fresh set up, I'm wondering if in my case its due to lack of meter data consent for my export MPAN? I don't see any consent for that in the Bright App.
My Display App firmware is 1.9.1 and the Zigbee firmware is 1.2.5.
My MQTT data for export is shown below and has been like this since Nov '22.
"export": {
"cumulative": 0,
"units": "kWh"
},
Before the change in Nov '22 I was able to get the total export value from the meter. So something changed on the 17th Nov on my meter that then prevented the IHD from reading the Export cumulative value. I presume this was the date when the DCC pushed new firmware\ settings to my meters?
Could you drop an email to my attention to support@ - I can then see what firmware versions is on your electricity meter, not our device.
FYI, the DCC only update the firmware on the Communications Hub - your energy supplier sends the meter firmware updates. On the other hand, ALL meter firmware versions have to be approved by the DCC.
Thanks @philporter - we'll get the list consolidated and over to the DCC for discussion with meter manufacturers as apparently the guidance in the Smart Energy Code is that instantaneous export should be published.
Hi, unfortunately I'm unsure how to work out the firmware version but I've just had an Aclara SGM1411-B SMETS2 meter fitted and it only shows 0 on the IHD.
Comments
Well, I've a SMETS2 meter - no sign of export ever having worked - other than on the meter's own display. So I'm not sure that's quite correct.
My meter is an Honeywell AS302P:
Using the local MQTT I do see a cumulative export figure but also expected the instantaneous export. well the current power to show positive for import and negative for export.
Is this possible without using a clamp? can the Glow MQTT show instantaneous export?
Hello @ianfretwell and @BNMBob - based on older comments in this thread, the instantaneous export question is possible with local MQTT, the challenge is meter type and firmware version.
What are yours if you know them - and if you don't, drop us a line at support and we can check. Thank you.
Hi Jane...
Mine is an EDMI ES-10B
https://www.edmi-meters.com/europe/product/meters/electricity-metering-devices/es-10b/
Thanks,
Ian
Hello Jane, I am waiting for my supplier to update the firmware on my Honeywell AS302P as DDC other is not supported. (i also do not see the firmware anywhere).
Once/IF done, Ill update this thread. Thank you
Hi @JaneatGlow, sorry about the slow response.
No I don't think my loss of MQTT export meter total data coincided with DCC migration. I lost the export total in Apr 22, and pretty sure I was switched sometime later in the year.
Hello @JaneatGlow, the update of firmware on my Honeywell AS302P is done. looks like its now 09014009.
No instantaneous Export.
Thanks
Hi @JaneatGlow - my meter is a Secure Liberty 100. Its been migrated over to the DCC last year. Sorry but I don't know how to get its firmware version. If you can point me at some instructions I will post back what it is.
Cheers,
Brodie
@bpeers - there is a screen on Bright in the Settings area that should give you the firmware. Are you getting your instantaneous export or not?
I am not seeing export being display on my display. These are my details.
Aclara electricity meter with firmware version 00070806, Model SGM1412B.
My Meter is a EDMI ES-10B, firmware 0314B700. I'm not seeing energy export data. Energy import and power are both fine.
As its a fresh set up, I'm wondering if in my case its due to lack of meter data consent for my export MPAN? I don't see any consent for that in the Bright App.
{ "electricitymeter": { "timestamp": "2023-04-06T15:04:18Z", "energy": { "export": { "cumulative": 0, "units": "kWh" } } } }Hi @JaneatGlow,
My Display App firmware is 1.9.1 and the Zigbee firmware is 1.2.5.
My MQTT data for export is shown below and has been like this since Nov '22.
"export": {
"cumulative": 0,
"units": "kWh"
},
Before the change in Nov '22 I was able to get the total export value from the meter. So something changed on the 17th Nov on my meter that then prevented the IHD from reading the Export cumulative value. I presume this was the date when the DCC pushed new firmware\ settings to my meters?
Thanks,
Brodie
Hi Brodie / @bpeers,
Could you drop an email to my attention to support@ - I can then see what firmware versions is on your electricity meter, not our device.
FYI, the DCC only update the firmware on the Communications Hub - your energy supplier sends the meter firmware updates. On the other hand, ALL meter firmware versions have to be approved by the DCC.
Complicated, isn't it!
Thanks for your help,
Jane
Hello @JaneatGlow to add to your list, I have an elster (Honeywell?) AS300P (Smets1) on firmware 0401D8C9 and have no instantaneous Export on MQTT.
Thanks
Phil
Thanks @philporter - we'll get the list consolidated and over to the DCC for discussion with meter manufacturers as apparently the guidance in the Smart Energy Code is that instantaneous export should be published.
Hi, unfortunately I'm unsure how to work out the firmware version but I've just had an Aclara SGM1411-B SMETS2 meter fitted and it only shows 0 on the IHD.
Hello @Freebo - thanks for your help - if you drop us an email to support@ we can look it up for you :)
I've recently set up my MQTT feed and, like others, my electricity export is showing as zero.
My meter is EDMI ES-10A, firmware 0314B700.